Форумы  ·  Войти  · 

Тема: TDA200 v3

15.12.05 14:22   vnvnvnvn  (6/14.10.05)  

У кого-нибудь есть уже? Поделитесь, plz.
MC pcprogv3000-R1 есть, оттуда New Featurei

Не выкладывается MC v3000-R1 на ftp. такая вот ошибка:
150 Opening BINARY mode data connection for pcprogv3000-R1.exe
Закачка
552 Transfer aborted. Disc quota exceeded


<< New Feature & New Programming >>

1. Configuration - 4. Option
// PRI23 mode decided when card is installed //
<Value Range>
ISDN Standard mode / T1-LCOT mode   (ISDN Standard is new option.)
<Description>
When a PRI23 card is installed for the first time,
this setting specifies whether it is automatically set to ISDN Standard mode or T1 mode.
A PRI23 card in ISDN Standard mode supports the following features:
  -CCBS, CF, CT and Centralised VM using QSIG service
  -Incoming call distribution (DIL or DID) for the D channel only
A PRI23 card in T1 mode supports the following features:
  -Incoming call distribution (DIL or DID) for all 23B channels.
CCBS, CF, CT and Centralised VM are not available for PRI23 cards in T1 mode.

2. System - 4. Timers & Counters - 3. Miscellaneous
// System Wireless : PS Out of Range Timer (s) //
<Value Range>
0s / 4s / 8s   (4s and 8s are new options.)
<Description>
When the destination of an incoming call is a PS, this setting specifies the length of time
the PBX searches for the PS, before setting the status of the PS to Out of Range.
If “0s” is assigned, the timer is controlled by the cell station.

2. System - 6. Numbering Plan - 7. Quick Dialling (MEC)
// Quick Dialling //
<Value Range>
4000 entries x 8 digits and 32 telephone numbers
<Description>
Quick dialling memory can be expanded using a memory expansion card (MEC).

2. System - 9. System Options - 4. Option 4
// Automatic Transfer by DSS key for Extension Call //
<Value Range>
Disable / Enable   (Disable is new option.)
<Description>
When disabled, if a DSS button is pressed during an extension-to-extension call,
the PBX disconnects the current call, and calls the extension assigned to the DSS button.

// Automatic Answer for Transferred Call //
<Value Range>
Disable / Enable   (Enable is new option.)
<Description>
When enabled, transferred calls (as well as direct extension calls) will be automatically answered
when using the Hands-free Answerback feature.

// Sending CLIP of Caller from CO (ICD Group with Cellular Phone) //
<Value Range>
Disable / Enable   (ICD Group with Cellular Phone is new feature.)
<Description>
When a trunk line call is received at an ICD Group containing a virtual PS,
selects whether the CLIP number of the original caller, or the CLIP number assigned to the virtual PS,
is sent to the virtual PS’s forwarding destination to identify the call origin.
The forward destination of a virtual PS is usually a cellular phone.
This setting only applies to calls automatically forwarded to public trunk lines using the ICD Group
with Cellular Phone feature.

// Common Extension Numbering for 2 PBXs //
<Value Range>
Disable / Enable   (Enable is new option.)
<Description>
When enabled, a network made up of two PBXs connected using QSIG and using the extension number method
can allow extensions at both PBXs to have the same leading number.
For example, extension 101 is registered at PBX 1, and extension 102 is registered at PBX 2.
The optional SD card is required for this feature.

// System Wireless Out of Range Registration //
<Value Range>
Disable / Enable   (Enable is new option.)
<Description>
When enabled, the PBX can set the status of a PS to Out of Range if no signal is received
from the PS for a preset length of time. This feature must be enabled to allow PS roaming.

// ISDN Alert Connection Mode //
<Value Range>
Disable / Enable   (Enable is new option.)
<Description>
When enabled, allows the voice path of an ISDN line to connect even when “alert” is received from ISDN.

3. Groups - 5. Incoming Call Distribution - 2. Member
// Extension No. //
<Value Range>
“Virtual PS” is also available as an ICD group member.
<Description>
ICD groups can contain cellular phones, and network ICD groups (ICD groups at other PBXs in a network).
The forward destination assigned to a virtual PS (e.g. a cellular phone) can act as a member of an ICD group.
The optional SD card is required for this feature.

3. Groups - 5. Incoming Call Distribution - 4. Miscellaneous
// Wrap-up Timer based on //
<Value Range>
Extension / ICD Group Member   (Extension is new option.)
<Description>
ICD group members can select one of two wrap-up timers. When Extension is selected,
the extension wrap-up timer is activated when making calls,
and receiving direct incoming calls and hold retrieve calls, as well as incoming calls through an ICD group.

// Longest Idle Distribution //
<Value Range>
Disable (UCD) / Enable (ACD)  (Enable is new option.)
<Description>
When enabled, automatic call distribution to the longest idle member in an ICD group is activated.
The optional SD card is required for this feature.

// ICD Group Key Mode //
<Value Range>
Standard (GDN) / Enhanced Phantom   (Enhanced Phantom is new option.)
<Description>
The Enhanced Phantom button feature can be set for ICD group buttons.
When an Enhanced Phantom key is created at an extension using PT personal programming,
the extension is automatically registered as a member of the relevant ICD group.

4. Extension - 1. Wired Extension - 1. Extension Settings
// Wrap-up Time //
<Value Range>
0s - 3000s
<Description>
Incoming calls through an ICD group are not distributed to the extension for the length of time set here,
after ending a call (incoming, outgoing, or hold retrieve call, in addition to calls from the ICD group).
This timer is used when “Wrap-up Timer based on” is set to Extension.

4. Extension - 1. Portable Station - 1. Extension Settings
// Wrap-up Time //
<Value Range>
0s - 3000s
<Description>
Incoming calls through an ICD group are not distributed to the extension for the length of time set here,
after ending a call (incoming, outgoing, or hold retrieve call, in addition to calls from the ICD group).
This timer is used when “Wrap-up Timer based on” is set to Extension.

5. Optional Device - 3. DISA - 1. System Setting
// Remote Walking COS without PIN //
<Value Range>
Disable / Enable   (Enable is new option.)
<Description>
When enabled, incoming calls to the message card with pre-registered caller ID numbers
can access DISA features without entering a PIN.
The optional SD card is required for this feature.

// CO-CO with DISA : Fwd/Transfer to Public CO //
<Value Range>
Disable / Enable (Get DISA)  (Enable is new option.)
<Description>
When enabled, end of call detection by DISA for trunk-to-trunk (public trunk) calls is performed.
DISA (message card) is activated automatically.

// CO-CO with DISA : Fwd/Transfer to Private Network //
<Value Range>
Disable / Enable (Get DISA)  (Enable is new option.)
<Description>
When enabled, end of call detection by DISA for trunk-to-trunk (private network) calls is performed.
DISA (message card) is activated automatically.

// CO-CO with DISA : DISA to Public CO //
<Value Range>
Disable (Release DISA) / Enable   (Disable is new option.)
<Description>
When disabled, DISA (message card) is released when a trunk-to-trunk (public trunk) call from DISA is made.

// CO-CO with DISA : DISA to Private Network //
<Value Range>
Disable (Release DISA) / Enable   (Disable is new option.)
<Description>
When disabled, DISA (message card) is released when a trunk-to-trunk (private network) call from DISA is made.

// Transfer by DTMF “#” //
<Value Range>
Disable (as DTMF “#”) / Enable (as “Flash”)  (Enable is new option.)
<Description>
When enabled, a party (such as a cellular phone) called on a trunk can transfer the call
by dialling “#” + extension number.
The optional SD card is required for this feature.

9. Private Network - 1. TIE Table
// Enhanced QSIG Call Information //
<Value Range>
Disable / Enable   (Enable is new option.)
<Description>
When enabled, enhanced QSIG information can be sent to the QSIG network for the Centralised VM feature.
Network message waiting information is sent from the PBX to which the VM is attached to other PBXs.
Time service, forward condition (busy, no answer, etc.) and so on are sent from other PBXs to the PBX
with VM for this feature.
The optional SD card is required for this feature.

9. Private Network - 2. Network Data Transfer
// Network MSW Data Re-transmission : Repeat Counter //
<Value Range>
0 - 10
<Description>
When network message waiting information cannot be sent from the PBX to which the VM is attached to other PBXs
because of a communication error, resending is attempted the number of times specified here.

// Network MSW Data Re-transmission : Interval Time //
<Value Range>
10 - 240s
<Description>
When network message waiting information cannot be sent from the PBX to which the VM is attached to other PBXs
because of a communication error, resending is attempted after waiting for the length of time specified here.

11. Maintenance - 4. Miscellaneous
// Error Log for Network MSW Transmission (Counter) //
<Value Range>
Disable / Enable   (Enable is new option.)
<Description>
When enabled, creates an error log entry if network message waiting information is deleted after re-transmission.

// Error Log for Network MSW Transmission (Buffer) //
<Value Range>
Disable / Enable   (Enable is new option.)
<Description>
When enabled, creates an error log entry if the quantity of network message waiting information being transmitted
is larger than the transmission buffer.

===================================================================

[ #1 ]  15.12.05 14:37   HPPY  (345/23.11.05)  

С почином, новые версии лучьше не ставить

Komendant.pro
 ©1999-2025  Инженерная лаборатория "Комендантъ"